英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字,中文词皆可:

anneal    音标拼音: [ən'il]
n. 退火

退火

anneal
v 1: bring to a desired consistency, texture, or hardness by a
process of gradually heating and cooling; "temper glass"
[synonym: {anneal}, {temper}, {normalize}]


请选择你想看的字典辞典:
单词字典翻译
anneal查看 anneal 在百度字典中的解释百度英翻中〔查看〕
anneal查看 anneal 在Google字典中的解释Google英翻中〔查看〕
anneal查看 anneal 在Yahoo字典中的解释Yahoo英翻中〔查看〕





安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Why anneal new brass? - The Firearms Forum
    I was looking at Midway's latest circular and noticed that new LC brass is annealed I also recall seeing several other military rounds that were annealed when new Got me thinking as to why they do this, and if it really is a big benefit, then why don't other manufacturers do it? Does anyone
  • Annealing . 223 Rem. Brass - The Firearms Forum
    Is it necessary to anneal 223 brass? I'm new to reloading rifle rounds thought that maybe because of it's lower velocity compared to larger bullets , that the heat wouldn't affect the 223 or the Nato
  • Teach me about annealing - The Firearms Forum
    I anneal my brass specifically to provide more even bullet neck tension because work-hardened brass tends to spring back when compressed or stretched Over time you can lose track of the amount of "spring-back" one will get on different brass so this is a way to regularize that value
  • Annealing Question - Body Anneal for New Unformed Brass
    Here's the note from Starline: This brass has not been annealed, and will require a body anneal prior to forming, and possibly a neck anneal after forming, depending on how far it is necked down I do have an annealing center, but it is set for necks
  • Am i Over annealing my brass? - The Firearms Forum
    I need to know if i over annealed any of this brass or do i need to toss it and get some more and start over there are a couple different annealing time lengths between some of the brass which you can see in the pictures When I stated the annealing I was trying to figure out the best duration
  • To dip . . . . . . or not to dip in water to cool brass after. . .
    To properly anneal steels requires slow cooling in a sand or oil bath in order to preserve ductility for further working Be very careful not to overheat the base of the cases; they are specially treated to resist the expansion forces of the burning powder, and if annealed may fail in practice
  • Case Annealing - The Firearms Forum
    Anneal cases before cleaning and before any sizing to make less work for brass Good time to debur the primer pocket if needed 1 LB propane last about 200 cases The blue flame length is set when just touching the neck shoulder bend for 308 per annealeez The blue flame tip length is about 3 8 - 1 4 inch back from the neck shoulder for 7-08
  • Annealing Brass with lead - The Firearms Forum
    Following the anneal, it would be wise to closely inspect the inside of the case both visually and with a bent paper clip just to make sure there are no lead drippings adhering to the inside the case Because it only takes a few seconds per case, you can anneal hundreds of cases in an hour with this method
  • Question about converting . 223 to 300 blackout - The Firearms Forum
    As to annealing, I have not seen a real need to anneal prior to forming I use a Hornady 3 die 300 Whisper set that has an expander die that nicely opens the 223 mouth and then run it into the chop saw using a form to limit my cut Then into the 300 whisper decap form die- trim to length using WFT with the 300 BLK insert Fast and accurate
  • The Ultimate Guide to Case Reforming | The Firearms Forum
    Case reforming is a skill that at its most basic, creates options where none may otherwise exist If you have a firearm in an obsolete cartridge, your ONLY option to fire it may be to make or acquire converted cartridge brass Often, obsolete brass may be so expensive to obtain that the cost of the reforming die set is quickly recovered once you process a few batches of brass These hobbies





中文字典-英文字典  2005-2009